Research |
![]() ![]() ![]() ![]() ![]() |
Serial Number | 78486518 |
Mark Drawing Code | 4000: Illustration: Drawing with word(s)/letter(s)/number(s) in Block form |
Law Office Assigned | M10 |
Employee Name | MILTON, PRISCILLA W |
2004-08-01 | Date of First Use |
2004-09-20 | Application Filed |
2005-10-22 | Abandon |
2005-11-22 | Location: TMO LAW OFFICE 110 - EXAMINING ATTORNEY ASSIGNED |
2005-11-22 | Status: Dead/Abandoned |
2018-07-08 | Transaction Date |
Owner: | ![]() |
Address | 1430 Gordon St Hollywood CA DE 90028 |
Legal Entity Type | Individual |
Legal Entity State | DE |
Click the blue "Refresh" button to load certificates, specimines, application, and other documents.
International Codes: | 9 |
U.S. Codes: | 021,023,026,036,038 |
Type Code | Type |
---|---|
GS0091 | The CD Wall-It is an innovative way to store and display your Compact Disc cases; The CD Wall-It system allows you to easily place any standard sized Compact Disc case into the patented "holder"; The "holder" is slightly larger than the Compact Disc case (Dimensions?) and holds the disk firmly in place with a claw like mechanism; Simply angle the Compact Disc case into the "holder" then lightly press down; The claw mechanism allows the consumer to open the doors of their Compact Disc cases while inside of the CD Wall-It "holder and still have full access to their Compact Disc; The "holder" has five small holes pre-drilled into it; There is one hole on each corner of the "holder" and one hole in the center; These holes allow you to easily attach the "holder" to the wall with anything from small picture frame nails to thumbtacks/ push-pins; The "holder" also comes with four pre-drilled attachment slots; These slots allow you to connect multiple "holders" to each other allowing the consumer to arrange their "holders" in a variety of different shapes; These attachment slots are found on the top, bottom, right side, and left side of each "holder" (2 x 1;1/2 x 0;1); Each slot is symmetrical with its corresponding slot, meaning the top is perfectly lined up with the bottom, right side perfectly lined up with the left side; The CD Wall-It's attachment system is based on two types of "shape connectors"; The "shape connectors" two-shapes are 1;) Flat, and 2;) Rounded 45-degree angle (1;1/8 x 1;1/8 x 1;1/2 x 01); All "shape connectors" have rounded ends and rounded sides; The rounded ends allow the "shape connectors" to slide easily into the attachment slots on the "holder", and the rounded sides avoid sharp plastic hard edges; Each "shape connector" also has four protuberances, two on the front side, and two on the backside; These protuberances are designed to stop the "shape connectors" from sliding too far into its respective attachment slot; These protuberances allow each "holder" to line up perfectly with every other "holder" when connected by preventing the "shape connectors" from sliding out of position; With these two different shapes, the consumer can create a wide variety of shapes and designs; The Flat "shape connectors" allow the "holders" to connect horizontally or vertically in any direction; An example of this would be to arrange "holders" all over a flat wall; The Rounded 45-degree angle "shape connector" allows for much more versatility; By using a combination of both, Rounded 45-degree angle and Flat "shape connectors", consumers can create 3 dimensional boxes that protrude from their walls, create a stair like effect, or wrap around corners |
Description | Date | Event Coding |
---|---|---|
NEW APPLICATION ENTERED IN TRAM | 2004-09-27 | 1 NWAP I:Incoming Correspondence |
ASSIGNED TO EXAMINER | 2005-04-20 | 2 DOCK D:Assigned to Examiner |
NON-FINAL ACTION WRITTEN | 2005-04-22 | 3 CNRT R:Renewal |
NON-FINAL ACTION E-MAILED | 2005-04-22 | 4 GNRT F:First Action |
ABANDONMENT - FAILURE TO RESPOND OR LATE RESPONSE | 2005-11-22 | 5 ABN2 O:Outgoing Correspondence |
ABANDONMENT NOTICE MAILED - FAILURE TO RESPOND | 2005-11-22 | 6 MAB2 O:Outgoing Correspondence |
uspto.report is an independent third-party trademark research tool that is not affiliated, endorsed, or sponsored by the United States Patent and Trademark Office (USPTO) or any other governmental organization. The information provided by uspto.report is based on publicly available data at the time of writing and is intended for informational purposes only.
While we strive to provide accurate and up-to-date information, we do not guarantee the accuracy, completeness, reliability, or suitability of the information displayed on this site. The use of this site is at your own risk. Any reliance you place on such information is therefore strictly at your own risk.
All official trademark data, including owner information, should be verified by visiting the official USPTO website at www.uspto.gov. This site is not intended to replace professional legal advice and should not be used as a substitute for consulting with a legal professional who is knowledgeable about trademark law.